Benutzer-Werkzeuge

Webseiten-Werkzeuge


cura_settings

Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen gezeigt.

Link zu dieser Vergleichsansicht

Both sides previous revision Previous revision
Next revision
Previous revision
cura_settings [2013/11/26 13:12]
fabian.frey
cura_settings [2013/11/26 15:24] (aktuell)
fabian.frey
Zeile 19: Zeile 19:
  
  
-Das durchsichtige PLA kann mit sehr niedriger Temperatur gedruckt werden. Ausserdem wird es wenn man 100% infill verwendet auch fast durchsichtig,​ wie ein stück ​Acrylglas.  +Das durchsichtige PLA kann mit sehr niedriger Temperatur gedruckt werden. Ausserdem wird es wenn man 100% infill verwendet auch fast durchsichtig,​ wie ein Stück ​Acrylglas.  
- +\\ 
- +\\ 
-[profile] +[profile]\\ 
-layer_height = 0.2 +layer_height = 0.2\\ 
-wall_thickness = 0.8 +wall_thickness = 0.8\\ 
-retraction_enable = True +retraction_enable = True\\ 
-solid_layer_thickness = 0.9 +solid_layer_thickness = 0.9\\ 
-fill_density = 99 +fill_density = 99\\ 
-nozzle_size = 0.4 +nozzle_size = 0.4\\ 
-print_speed = 50 +print_speed = 50\\ 
-print_temperature = 193 +print_temperature = 193\\ 
-print_temperature2 = 0 +print_temperature2 = 0\\ 
-print_temperature3 = 0 +print_temperature3 = 0\\ 
-print_temperature4 = 0 +print_temperature4 = 0\\ 
-print_bed_temperature = 55 +print_bed_temperature = 55\\ 
-support = None +support = None\\ 
-platform_adhesion = None +platform_adhesion = None\\ 
-support_dual_extrusion = Both +support_dual_extrusion = Both\\ 
-wipe_tower = False +wipe_tower = False\\ 
-ooze_shield = False +ooze_shield = False\\ 
-filament_diameter = 2.85 +filament_diameter = 2.85\\ 
-filament_diameter2 = 0 +filament_diameter2 = 0\\ 
-filament_diameter3 = 0 +filament_diameter3 = 0\\ 
-filament_diameter4 = 0 +filament_diameter4 = 0\\ 
-filament_flow = 100.0 +filament_flow = 100.0\\ 
-retraction_speed = 40.0 +retraction_speed = 40.0\\ 
-retraction_amount = 4.5 +retraction_amount = 4.5\\ 
-retraction_dual_amount = 16.5 +retraction_dual_amount = 16.5\\ 
-retraction_min_travel = 1 +retraction_min_travel = 1\\ 
-retraction_combing = True +retraction_combing = True\\ 
-retraction_minimal_extrusion = 0.1 +retraction_minimal_extrusion = 0.1\\ 
-bottom_thickness = 0.3 +bottom_thickness = 0.3\\ 
-object_sink = 0 +object_sink = 0\\ 
-overlap_dual = 0.2 +overlap_dual = 0.2\\ 
-travel_speed = 150.0 +travel_speed = 150.0\\ 
-bottom_layer_speed = 30 +bottom_layer_speed = 30\\ 
-infill_speed = 80 +infill_speed = 80\\ 
-cool_min_layer_time = 5 +cool_min_layer_time = 5\\ 
-fan_enabled = True +fan_enabled = True\\ 
-skirt_line_count = 1 +skirt_line_count = 1\\ 
-skirt_gap = 3.0 +skirt_gap = 3.0\\ 
-skirt_minimal_length = 150.0 +skirt_minimal_length = 150.0\\ 
-fan_full_height = 0.5 +fan_full_height = 0.5\\ 
-fan_speed = 25 +fan_speed = 25\\ 
-fan_speed_max = 66 +fan_speed_max = 66\\ 
-cool_min_feedrate = 0 +cool_min_feedrate = 0\\ 
-cool_head_lift = False +cool_head_lift = False\\ 
-solid_top = True +solid_top = True\\ 
-solid_bottom = True +solid_bottom = True\\ 
-fill_overlap = 100 +fill_overlap = 100\\ 
-support_fill_rate = 15 +support_fill_rate = 15\\ 
-support_xy_distance = 1.5 +support_xy_distance = 1.5\\ 
-support_z_distance = 0.2 +support_z_distance = 0.2\\ 
-spiralize = False +spiralize = False\\ 
-brim_line_count = 20 +brim_line_count = 20\\ 
-raft_margin = 5 +raft_margin = 5\\ 
-raft_line_spacing = 1.0 +raft_line_spacing = 1.0\\ 
-raft_base_thickness = 0.3 +raft_base_thickness = 0.3\\ 
-raft_base_linewidth = 0.7 +raft_base_linewidth = 0.7\\ 
-raft_interface_thickness = 0.2 +raft_interface_thickness = 0.2\\ 
-raft_interface_linewidth = 0.2 +raft_interface_linewidth = 0.2\\ 
-fix_horrible_union_all_type_a = False +fix_horrible_union_all_type_a = False\\ 
-fix_horrible_union_all_type_b = False +fix_horrible_union_all_type_b = False\\ 
-fix_horrible_use_open_bits = False +fix_horrible_use_open_bits = False\\ 
-fix_horrible_extensive_stitching = False +fix_horrible_extensive_stitching = False\\ 
-plugin_config = (lp1 +plugin_config = (lp1\\ 
-+.\\ 
-object_center_x = -1 +object_center_x = -1\\ 
-object_center_y = -1 +object_center_y = -1\\ 
- +\\ 
-[alterations] +[alterations]\\ 
-start.gcode = ;Sliced at: {day} {date} {time} +start.gcode = ;Sliced at: {day} {date} {time}\\ 
- ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} +;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}\\ 
- ;Print time: {print_time} +;Print time: {print_time}\\ 
- ;Filament used: {filament_amount}m {filament_weight}g +;Filament used: {filament_amount}m {filament_weight}g\\ 
- ;Filament cost: {filament_cost} +;Filament cost: {filament_cost}\\ 
- ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line +;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line\\ 
- ;M109 S{print_temperature} ;Uncomment to add your own temperature line +;M109 S{print_temperature} ;Uncomment to add your own temperature line\\ 
- G21        ;metric values +G21        ;metric values\\ 
- G90        ;absolute positioning +G90        ;absolute positioning\\ 
- M107       ;​start with the fan off +M107       ;​start with the fan off\\ 
- G28 X0 Y0  ;move X/Y to min endstops +G28 X0 Y0  ;move X/Y to min endstops\\ 
- G28 Z0     ;move Z to min endstops +G28 Z0     ;move Z to min endstops\\ 
- G1 Z15.0 F{travel_speed} ;move the platform down 15mm +G1 Z15.0 F{travel_speed} ;move the platform down 15mm\\ 
- G92 E0                  ;zero the extruded length +G92 E0                  ;zero the extruded length\\ 
- G1 F200 E3              ;extrude 3mm of feed stock +G1 F200 E3              ;extrude 3mm of feed stock\\ 
- G92 E0                  ;zero the extruded length again +G92 E0                  ;zero the extruded length again\\ 
- G1 F{travel_speed} +G1 F{travel_speed} 
- ;Put printing message on LCD screen +;Put printing message on LCD screen\\ 
- M117 Printing... +M117 Printing...\\ 
-end.gcode = ;End GCode +end.gcode = ;End GCode\\ 
- M104 S0                     ;​extruder heater off +M104 S0                     ;​extruder heater off\\ 
- M140 S0                     ;​heated bed heater off (if you have it) +M140 S0                     ;​heated bed heater off (if you have it)\\ 
- G91                                    ;relative positioning +G91                                    ;relative positioning\\ 
- G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release ​some of the pressure +G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release ​ome of the pressure\\ 
- G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more +G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more\\ 
- G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way +G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way\\ 
- M84                         ;​steppers off +M84                         ;​steppers off\\ 
- G90                         ;​absolute positioning +G90                         ;​absolute positioning\\ 
-start2.gcode = ;Sliced at: {day} {date} {time} +tart2.gcode = ;Sliced at: {day} {date} {time}\\ 
- ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} +;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}\\ 
- ;Print time: {print_time} +;Print time: {print_time}\\ 
- ;Filament used: {filament_amount}m {filament_weight}g +;Filament used: {filament_amount}m {filament_weight}g\\ 
- ;Filament cost: {filament_cost} +;Filament cost: {filament_cost}\\ 
- ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line +;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line\\ 
- ;M104 S{print_temperature} ;Uncomment to add your own temperature line +;M104 S{print_temperature} ;Uncomment to add your own temperature line\\ 
- ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line +;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line\\ 
- ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line +;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line\\ 
- G21        ;metric values +G21        ;metric values\\ 
- G90        ;absolute positioning +G90        ;absolute positioning\\ 
- M107       ;​start with the fan off +M107       ;​start with the fan off\\ 
- G28 X0 Y0  ;move X/Y to min endstops +G28 X0 Y0  ;move X/Y to min endstops\\ 
- G28 Z0     ;move Z to min endstops +G28 Z0     ;move Z to min endstops\\ 
- G1 Z15.0 F{travel_speed} ;move the platform down 15mm +G1 Z15.0 F{travel_speed} ;move the platform down 15mm\\ 
- T1                      ;Switch to the 2nd extruder +T1                      ;Switch to the 2nd extruder\\ 
- G92 E0                  ;zero the extruded length +G92 E0                  ;zero the extruded length\\ 
- G1 F200 E10             ;​extrude 10mm of feed stock +G1 F200 E10             ;​extrude 10mm of feed stock\\ 
- G92 E0                  ;zero the extruded length again +G92 E0                  ;zero the extruded length again\\ 
- G1 F200 E-{retraction_dual_amount} +G1 F200 E-{retraction_dual_amount}\\ 
- T0                      ;Switch to the first extruder +T0                      ;Switch to the first extruder\\ 
- G92 E0                  ;zero the extruded length +G92 E0                  ;zero the extruded length\\ 
- G1 F200 E10             ;​extrude 10mm of feed stock +G1 F200 E10             ;​extrude 10mm of feed stock\\ 
- G92 E0                  ;zero the extruded length again +G92 E0                  ;zero the extruded length again\\ 
- G1 F{travel_speed} +G1 F{travel_speed}\\ 
- ;Put printing message on LCD screen +;Put printing message on LCD screen\\ 
- M117 Printing... +M117 Printing...\\ 
-end2.gcode = ;End GCode +end2.gcode = ;End GCode\\ 
- M104 T0 S0                     ;​extruder heater off +M104 T0 S0                     ;​extruder heater off\\ 
- M104 T1 S0                     ;​extruder heater off +M104 T1 S0                     ;​extruder heater off\\ 
- M140 S0                     ;​heated bed heater off (if you have it) +M140 S0                     ;​heated bed heater off (if you have it)\\ 
- G91                                    ;relative positioning +G91                                    ;relative positioning\\ 
- G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure +G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure\\ 
- G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more +G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more\\ 
- G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way +G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way\\ 
- M84                         ;​steppers off +M84                         ;​steppers off\\ 
- G90                         ;​absolute positioning +G90                         ;​absolute positioning\\ 
-support_start.gcode =  +support_start.gcode = \\ 
-support_end.gcode =  +support_end.gcode = \\ 
-cool_start.gcode =  +cool_start.gcode = \\ 
-cool_end.gcode =  +cool_end.gcode = \\ 
-replace.csv =  +replace.csv = \\ 
-switchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders. +switchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.\\ 
- G92 E0 +G92 E0\\ 
- G1 E-36 F5000 +G1 E-36 F5000\\ 
- G92 E0 +G92 E0\\ 
- T{extruder} +T{extruder}\\ 
- G1 X{new_x} Y{new_y} Z{new_z} F{travel_speed} +G1 X{new_x} Y{new_y} Z{new_z} F{travel_speed}\\ 
- G1 E36 F5000 +G1 E36 F5000\\ 
- G92 E0+G92 E0\\
  
  
cura_settings.1385467942.txt.gz · Zuletzt geändert: 2013/11/26 13:12 von fabian.frey